background image

  9 

MAINTENANCE 

To prolong the service life and to ensure the maximum 

performance of the searchlight, we recommend the following 
maintenance guidelines : 

Dirt on front glass and/or mirror reflector will result in a 

considerable loss of light.  Before every voyage the equipment 
should be checked on these points as well as on good working of 
the lamp. 

 
Periodical maintenance is recommended at least once every three months. 
 
Before opening the searchlight for cleaning and/or inspection of the interior the supply 
must be disconnected. 
 
Procedure : 
Remove front glass and bezel assembly 
 
Inspect the lampholder, ensure that it is free from dirt and corrosion. 
Inspect the lamp. The quartz envelope must be bright and clear. 
Replace if necessary. 
 
Check all seals and rubber mountings of the mirror reflector. 
Replace if necessary. 
 
Check earthing point for conductivity 
 
Check small ventholes in the bottom to be open  
 
Check lamp supply cable on wear and tear. 
 
After the inspection : Clean frontglass inside and outside, and clean the mirror reflector 
with a proprietary glass cleaner. Cleaning the mirror reflector  does not harm the 
silvering because the silver layer is on the back of the glass. 
 
Finally : Test searchlight for full working for 20 odd minutes. 

 
 
 
 
 

Summary of Contents for IM400RCX























Reviews: