background image

PROBLEM: The walking belt is off-center

SOLUTION: a. If the walking belt has shifted to the left, first re-

move the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt clockwise, and the right bolt counterclock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered. 

b. If the walking belt has shifted to the right, first re-

move the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt counterclockwise, and the right bolt clock-
wise, 1/4 of a turn each. Be careful not to overtighten
the walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until
the walking belt is centered.

c. If the walking belt slips when walked on, first remove

the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn both rear roller adjustment bolts
clockwise 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each side of
the walking belt 3 to 4 inches off the walking platform.
Be careful to keep the walking belt centered. Plug in
the power cord, insert the key and carefully walk on
the treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.

PROBLEM: The Speed/Minutes-Mile display on the console does not function properly

SOLUTION: a. Remove the key from the console and unplug the power cord.

Remove Side Shield A (60) from the right side of the
treadmill by pressing down on the top of the Side
Shield and then pulling it away from the Motor Hood
(39). Remove Side Shield A (60) from the left side of
the treadmill by pressing down on the top and then
pulling it towards the Motor Hood. Next, remove the
three Screws (43) from Side Shield B (59) on each
side of the treadmill and remove both Side Shields. 

Remove the Screws (not shown) from the Motor Hood
(39). Carefully remove the Motor Hood. 

Locate the Reed Switch (17) and the Magnet (12) on the
left side of the Pulley (11). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure that
the gap between the Magnet and the Reed Switch is
about 1/8”. 
If necessary, loosen the Reed Switch Screw
(26) and move the Reed Switch slightly. Retighten the
Screw. Reattach the Motor Hood (39) and run the tread-
mill for a few minutes to check for a correct speed read-
ing. Reattach the four Side Shields (59, 60).

b

c

12

17

26

1/8”

11

Top 

View

39

59

59

43

60

60

a

26

Summary of Contents for 10.6QL



































Reviews: