iM3 HCR-100 Operation Manual Download Page 3

 

 

others. These are classified by degree of danger, damage and seriousness. All indicators concern 
safety and should be followed. 
 

Classification 

Degree of Danger or Damage and Seriousness 

 

DANGER 

Explains an instruction where death or serious injury may occur. 
 

WARNING 

Explains an instruction where bodily injury or damage to device may occur. 
 

CAUTION 

Explains an instruction where possibility for minor to medium bodily injury or 
damage to device may exist. 
 

 

DANGER 

 

Do not install, use this product or fill it with maintenance oil in room with a risk of explosion or    
flames. 

 

Do not install or use the product in direct sunlight or where the temperature exceeds 40C (104F) 

 

Do not use the product for other purposes than the maintenance (cleaning and lubrication) of 
handpieces described in this operation manual. 

 

Provide adequate ventilation. In the unlikely event of odours seek immediate ventilation.

 

 

WARNING 

 

Do not handle the power cord with wet hands. 

 

Be careful not to spill water onto the unit. May result in fire, electric shock or short-circuit.   

 

Do not disassemble or alter the unit. In case of service or repair, contact your dealer. 

 

In unlikely event of burning or smoke, immediately turn off the power switch and disconnect the 
power plug. Contact your dealer. 

 

Do not drop the unit. Place the unit on a flat surface. 

 

Only use fuses with rating, 120v: T800mAl250V, 220v/240v: T400mAl250V

 

 

 

Summary of Contents for HCR-100













Reviews: