2
1-877-540-5588
iluminarlighting.com
THANK YOU
for purchasing an
ILUMINAR Lighting Remote Ballast
. We strive to deliver the best
customer service alongside world-class products and we go above and beyond to make sure you are
beyond satisfied with your purchase. The following is a general set of warnings and basic guidelines for
the ILUMINAR remote ballasts. Always have an expert install your product(s) when possible.
KEEP ORIGINAL PACKAGING
In the event of a return, products will need to be in the original ILUMINAR packaging to avoid product
damage during shipping. Any damage to products not in their original packaging will not be covered
under Warranty. To read more about our product warranty, visit www.iluminarlighting.com/warranty.
SAFETY 1ST
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN ELECTRICAL SHOCK AND
SERIOUS INJURY. Additionally, failure to follow these safety warnings can/will result in a void all warranties
as well as any manufacturer liability.
Please read carefully prior to beginning installation.
This ballast is compatible only with the ILUMINAR Lighting fixtures. Do not connect any other device to the
Control Port. Any attempt to connect it to an incompatible fixture may result in damage to the ballast and will
void the warranty.
This ballast is intended for indoor and greenhouse applications only. Position it in an area away from excessive
heat or contact with liquids.
Make sure the power cord and lamp cord are correctly connected.
For remote operations, use this ballast with a maximum power cable of 15 feet (240v Nema provided).
Lamps with built-in igniters will not work with this ballast. Not for use with external ignitors.
Disconnect the ballast from the power supply prior moving the unit or performing any maintenance or lamp
changes.
DO NOT open the ballast case, it will void the warranty.
DO NOT support the ballast by power cord(s) and/or lamp cord(s). These cords/connections are not designed
to bear weight.
DO NOT make contact with the interior of the socket while power is on.
DO NOT plug the system into untested or unidentified voltage other than what is designated on ballast.
DO NOT attempt to rewire, alter, modify or reconfigure your system - this will void the ILUMINAR warranty and
could cause serious safety hazards, or cause bodily injury or death, as this is a high amperage and voltage
device.
DO NOT submerge in water.
DO NOT EVER CONNECT A CMH BALLAST to a Flip Box. It will void the warranty and can cause electrical failure
within the CMH Ballast. Flip or Switch Boxes are not recommended for any CMH Units or for any high wattage
ballasts.
DO NOT plug or unplug the lamp cord while the ballast is connected to power.
Keep away from Children.This product contains delicate electronic components. If it is placed near an object
that transmits radio signals, it could cause interference (i.e.: mobile devices, walkie talkies, CB radios, remote
controls and microwaves). If interference occurs, move such objects away from the appliance.
WARNINGS
750W
DE REMOTE BALLAST
178mm / 7.01”
275mm / 10.83”
113mm
4.45”
© Copyright 2021 ILUMINAR Lighting
Subject to change without notice.
iluminarlighting.com
Toll Free: 1-877-540-5588
Input Current
Input Power
Output Power
Min Power Factor
THD
Crest Factor
BTU
Inrush Current
2.91A
790W
Rated Voltage
Voltage Range (+/-10%)
Plug Type
Dimming Type
Frequency
Operational Frequency
Operation Temp.
Relative Humidity
Max. Humidity
Remote Mounting
Ignition Voltage
277V
249V-305V
Male NEMA L7-15 Twist Lock
OUTPUT SPECIFICATIONS
Case Length
Case Width
Height
Weight
PHYSICAL SPECIFICATIONS
120-240V
108-264V
Male NEMA 6-15
400-500-600-750-825-EXT
50/60Hz
100-120kHz
0 - 35°C / 32-95°F
85%
95%
5m/16ft
5kV
120V
277V
240V
INPUT SPECIFICATIONS
6.7A
805W
3.5A
795W
750W
0.99
<10%
<1.7
150
≤ 37.5 Amps
HPS/MH
275mm
178mm
113mm
3.5kg
10.83"
7.01"
4.45"
7.71lb
End of Lamp Life (EOL) Protection
Short Circuit Protection
Open Circuit Protection
Ignition Failure Protection
Thermal Protection
PROTECTIONS
VOLTAGE:
120V/240V
277V
SKU:
IL-RMDE750-240
IL-RMDE750-277
3
