background image

11

TB-CUT25-I

CHARGING A HOT OR COLD BATTERY PACK

The Red Flashing Indicator light on the charger indicates that the battery pack temperature is 

outside the charging range. Once the battery pack is within the acceptable range, normal charging 

will take place and the red light will be continuous. Hot or cold batteries may take longer to charge. 

POWER THE CHARGER WITH AN INVERTER OR GENERATOR

The charger will operate with most generators and inverters rated at 350 Watts or higher.

MAINTENANCE AND STORAGE

Store your charger in a cool, dry place. As a general practice, it is best to unplug battery chargers 

and remove batteries when not in use. No battery pack damage will occur, however, if the charger 

and battery pack are left plugged in.

REPAIRS

The charger has no serviceable parts.

MOUNTING TO THE WALL

Use the wall mount guides to mark the hanging points.

 

         To reduce the risk of injury, always unplug the charger and remove the battery from 

the charger before performing any maintenance. Never disassemble the battery or charger. 

Contact a MILWAUKEE service facility for ALL repairs. 

To reduce the risk of injury and damage, never immerse your battery or charger in liquid or allow a 

liquid to flow inside them.

CLEANING

Clean out dust and debris from charger vents and electrical contacts by blowing with compressed 

air. Use only mild soap and a damp cloth to clean the battery pack and charger, keeping away from 

all electrical contacts. Certain cleaning agents and solvents are harmful to plastics and other 

insulated parts. Some of these include gasoline, turpentine, lacquer thinner, paint thinner, chlo-

rinated cleaning solvents, ammonia and household detergents containing ammonia. Never use 

flammable or combustible solvents around batteries, charger, or tools. 

Summary of Contents for TaskMaster TB-CUT25-I

























Reviews: