Ikelite SLR-DC Housing Instruction Manual Download Page 10

Page: 10 / 32

DS50 and DS125 Strobe Compatibility

- Older

DS50

Strobes with Serial Number below 63,850 can NOT be

updated to operate correctly with the latest TTL conversion circuitry.

Older

DS50

Strobes with Serial Number between 63,850 and 69,999

require upgrade of electronics to operate. Strobe must be returned to

Ikelite for evaluation to provide an estimate of upgrade cost.

- Older

DS125

Strobes with Serial Number below 2,500 can NOT be

updated to operate correctly with the latest TTL conversion circuitry.

Older

DS125

Strobes with Serial Number between 2,500 and 4,999

require upgrade of electronics to operate. Strobe must be returned to

Ikelite for evaluation to provide an estimate of upgrade cost.

Attaching the Flash Connection for External Strobes

When using an external

strobe, connect the

housing hotshoe connector.

Slide the connector into the

hotshoe mount on the

camera from the back of

the camera as shown.

Slide the connector forward

until it stops. Due to limited

clearance between the

camera hotshoe mount and

the housing back, the

hotshoe connector should

be attached

before

the

camera is secured with the

mounting bolt.

NOTE:

The camera’s built-in flash is not accessible in the

housing.

Fron

External Strobe Connector

and Waterproof Cap

Housing Back

Hotshoe

Connector

Summary of Contents for SLR-DC Housing

































Search results

Summary of Contents for SLR-DC Housing

Reviews:

Related manuals for SLR-DC Housing

Brands by name

Popular brands

Ikelite SLR-DC Housing, Instruction Manual

Search results

Summary of Contents for SLR-DC Housing

Reviews:

Related manuals for SLR-DC Housing

Brands by name

Popular brands