8
CChheecckkiinngg CCoonnttrroollss
Once the housing has been closed, push the controls back into
place. Make sure they line up with the camera’s controls.
TTuurrnn CCaam
meerraa O
Onn
Turn the camera on and operate each of the housing controls
to get a feel for using the camera in the housing. Take a few
pictures above water with the camera in the housing.
ZZoooom
m CCoonnttrrooll
(NOTE:) After you have used the
housing's zoom control it must be
returned to the center position to
disengage. If the housing zoom
control is pushing the zoom lever
in either direction you may not
be able to take a picture or access
any other function as the camera
is receiving a signal from the
engaged zoom control.
LLuubbrriiccaannttss
1. Ikelite provides silicone lubricant with the housing. We recommend
you use only Ikelite lubricant on Ikelite products as some other
brands may cause the o’ring to swell and not seal properly.
2. Use only enough lubricant to lightly cover control shafts and
o’rings. Wipe off any excess lubricant with a clean cloth.
Lubricant is not a sealant, it is used to reduce friction. Excessive
lubricant can collect sand and dirt which may interfere with
proper sealing.
CCAAU
UTTIIO
ON
N
N
Neevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
c
caauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
+
-
+
-
Zoom control
engaged
Zoom control
disengaged
(centered)
7
CClloossiinngg tthhee H
Hoouussiinngg
1. Place housing face down in your
lap or on a flat surface.
2. Check to see that there is an
o’ring on the housing back and
that it is clean and in its proper
location.
3. Guide the back onto the housing.
The o’ring should touch the
housing all the way around. There
should be an even gap all the way
around between the housing and
the housing back.
4. Lift the lid snaps so they are
extended and place the lid snap
into the hook on the housing
back.
5. To close the housing push
down on the lid snaps until
they snap into place . Lid
snaps on opposite sides of the
housing should be closed at the
same time. Be sure they are down
far enough to engage the lock.
D
Doouubbllee cchheecckk - Once the housing is closed, check the o’ring seal.
Check the gap between the housing back and the housing, it
should be even all the way around.
Look through the clear plastic back at the o’ring. You should see
a darkened area where the o’ring is compressed against the
housing back. If you do not see an even black compression seal
all the way around the back, open the lid snaps, reseat the
housing back and close the lid snaps. Visually check the seal again.
o’ring
housing back
housing back
housing
housing
o’ring
even gap
all 4 sides
5
FFllaasshh CCoonnnneeccttiioonn ffoorr EExxtteerrnnaall SSttrroobbeess
When using an external strobe connect the housings Hot Shoe
Connector. Slide the connector into the hot shoe of the camera
from the back of the camera as shown. Slide the connector
forward until it stops. This should be done before the camera
is secured with the mounting bolt.
CCaauuttiioonn::
DDoo nnoott rreem
moovvee tthhee EExxtteerrnnaall SSttrroobbee CCoonnnneeccttoorr’’ss w
waatteerrpprrooooff ccaapp
uunnlleessss aann eexxtteerrnnaall ssyynncc ccoorrdd iiss ggooiinngg ttoo bbee pplluuggggeedd iinn..
External Strobe Connector
Waterproof Cap (see caution)
Hot Shoe
Connector
Housing Back
Silver
Mounting
Bracket
O’ring
Camera
6
IIff yyoouu aarree nnoott uussiinngg tthhee EExxtteerrnnaall FFllaasshh CCoonnnneeccttiioonn
Store the hot-shoe by sliding it into the silver bracket located on
the inside back of the camera housing as shown. This can be done
after the camera is mounted to the mounting tray.
CCAAU
UTTIIO
ON
N
O
Onnllyy rreem
moovvee tthhee W
WaatteerrPPrrooooff ccaapp ffrroom
m tthhee eexxtteerrnnaall ssttrroobbee
ccoonnnneeccttoorr oonn tthhee bbaacckk ooff tthhee hhoouussiinngg w
whheenn aann eexxtteerrnnaall ssttrroobbee
w
wiillll bbee ccoonnnneecctteedd..
Silver
Mounting Bracket
Hot Shoe
Top Edge
of Housing
