26
27
Spindle:
In this menu, you can select a required spindle for measuring�
1� List: According to the rough viscosity of the media to select a required spindle from the spindle list under
different spindle groups (Standard spindle, Spiral, ELVAS���)� A tick (√) show the selected spindle and group�
2� Search: According to required speed and rough viscosity of the media to select a required spindle�
Note:
The maximum viscosity (full scale range) can be automatically calculated basing on the selected spin-
dle, the speed and the integrated spring series (lo-vi/me-vi/hi-vi I/hi-vi II)�
Temperature:
Probe Temperature:
In this menu, you can check the temperature of the media when the temperature sensor is connected�
Display:
In this menu, you can specify the measured temperature value on the screen� A tick (√) show that the option
is activated�
Calibration:
In this menu, you can calibrate the connected temperature sensor with help of an external standard reference
temperature thermometer�
Note:
The temperature sensor must be calibrated whenever it is replaced or changed, or if a new temperature
sensor is installed� The temperature sensor supplied with the system is calibrated in factory�
Display:
Temperature:
In this menu, you can specify the measured temperature value on the screen� A tick (√) show that the option
is activated�
Level meter:
In this menu, you can check the levelling status of the device�
Graph:
Axis Assignment:
In this menu you can select 2 parameters from the 7 options (shear rate, shear stress, speed���) for axis
assignment� The ticks (√) show that the options that are activated� The selected parameters will be used for
the graph in the profile�
Axis scale:
When parameter “Time“ is not selected, the menu option “Axis scale“ is disabled and shown in grey color�
When you select “Time“ as one axis, the “Axis scale” gets enabled and can be edited� You can select 15, 30,
60 or 120 minutes as the axis scale� The selected scale will be used for the graph in the profile�
Program:
Program:
In this menu, 5 user-defined “speed-time” profiles can be created� A program can consist of up to 10 segments�
Once a program has been selected, the following options are available:
1� Start:
Starts the program upon request of loop mode�
Infinite loop:
Upon completion of the last segment, the program continues with the first segment until
the user ends the program by stopping a device function�
Loop count:
Indicates the total number of loop cycles until program end�
When the selected program is started by pressing on menu option “Start” with rotary/push knob, screen
reminds the user to confirm the program (PR) control� Press “OK” with rotary/push knob to start the
program control�
Note:
At the end of the program all device functions are switched off�
2� Edit:
Edit/change the selected program by pressing on the button “Edit“ with rotary/push knob�
Start to edit the selected program parameters (speed and time ) by pressing on the selected program� You
can “Edit”, “Delete“, “Insert“ and “Save“ the program segment with the rotary/push knob�
When you edit the program for at least one segment, symbol ( ) for respective program will appear�
In a program, user can define up to 10 program segments� The selected program segment is highlighted
in blue color� Then, the user can edit, delete, insert or save segment in this program by rotating/pressing
on the rotary/push knob�
When editing a parameter (Speed / Time), press the rotary/push knob on the selected parameter� The
highlighted cursor changed into yellow color indicate that parameter can be edited by rotating the rotary/
push knob�
When the “Back” button is pressed after editing, the program is saved after pressing on “OK“ as reminding
in the screen�
3� Delete:
Delete the selected program by pressing on the button “Delete“ with rotary/push knob�
If a selected program is deleted by pressing on menu option “Delete” with rotary/push knob, all the program
parameters will be emptied� The symbol ( ) disappears�
4� View:
View the “Speed (rpm)-Timer (hh:mm:ss)“ graph of the selected program by pressing on the button “View“
with rotary/push knob�
5� Rename:
Rename the selected program by pressing on the button “Rename“ with rotary/push knob�
Summary of Contents for ROTAVISC
Page 1: ...IKA ROTAVISC...
Page 2: ...ENGLISH...
