background image

Superiorfireplaces.US.com

126721-01_D

24

Figure 37 - Turning Equipment Shutoff Valve to the OFF Position

OPERATION

FOR YOUR SAFETY  

READ BEFORE LIGHTING

 WARNING: If you do not follow these instructions 

exactly, a fire or explosion may result causing property 

damage, personal injury or loss of life.

A. This appliance is equipped with an ignition device 

which automatically lights the pilot. Do not light pilot 

by hand.

B. BEFORE LIGHTING smell all around the appliance 

area for gas. Be sure to smell next to the floor be-

cause some gas is heavier than air and will settle 

on the floor.

  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electric switch; do not use any 

phone in your building.

•  Immediately call your gas supplier from a neigh-

bor's phone. Follow the gas supplier's instructions.

•  If you cannot reach your gas supplier, call the fire 

department.

C. If any portion of this appliance does not operate as 

the instructions indicate, do not try to repair it, call a 

qualified service technician. Do not use tools. Force 

or attempted repair may result in a fire or explosion.

D. Do not use this appliance if any part has been under 

water. Immediately call a qualified service technician 

to inspect the appliance and to replace any part of the 

control system and any gas control which has been 

under water.

LIGHTING 

INSTRUCTIONS

NOTICE: During initial operation of new fireplace, burn-

ing logs will give off a paper-burning smell. Orange 

flame will also be present. Open damper or window 

to vent smell. This will only last a few hours.

1.  STOP! Read the safety information in column 1.
2.  Turn off all electric power to fireplace.
3.  Turn safety shutoff switch to the OFF position.
4.  Remove center brick/control cover.
5.  Turn equipment shutoff valve clockwise 

 to the OFF position 

(see Figure 37). Do not force.

6.  Wait five (5) minutes to clear out any gas. Then smell for gas, 

including near the floor. If you smell gas, STOP! Follow “B” in the 

safety information, column 1. If you don't smell gas, go to the 

next step.

7.  Turn equipment shutoff valve counterclockwise 

 to the ON 

position. Do not force.

8.  Replace center brick/control cover.
9.  Turn on all electric power to appliance.
10. Turn safety shutoff switch to the ON position.
11. Visually locate pilot. Igniter should begin to spark and main burner 

should ignite once flame appears at pilot.
• If lighting appliance for the first time each season, it may take 

several attempts before supply gas can reach pilot and main 

burners.

• If appliance will not stay lit after several attempts, follow instruc-

tions under To Turn Off Gas To Appliance and call your service 

technician or gas supplier.

TO TURN OFF GAS 

TO APPLIANCE

1.  Turn off safety shutoff switch.
2.  Turn off all electric power to appliance if service is to be performed.
3.  Remove center brick/control cover.
4.  Turn equipment shutoff valve clockwise 

 to OFF. Do not force.

5.  Replace center brick/control cover.

MAIN

IN

OUT

PILOT

ADJ

PILOT

Equipment 

Shutoff Valve

Incoming 

Gas Line

Summary of Contents for Superior DRT4036TEN









































Reviews: