background image

IHP: RC-S-TOUCH

REV. 3-18-14 Page 8

WALL MOUNT

The transmitter can be placed on a wall using the mount provided.

Wood - Drill 1/8’’ pilot holes and install with screws provided.

• 

Plaster/Wallboard - Drill 1/4’’ holes, use a hammer to tap in the two plastic 

• 

anchors. Then install with the screws provided.

Fig. 26

BATTERY LIFE

Life expectancy of the alkaline batteries in the transmitter and receiver should be at least 12 months.  Check and replace 

all batteries:

Annually.

• 

When operating range becomes reduced.

• 

When transmissions are not received by the remote receiver.

• 

If the remote receiver batteries measure less than 5.3 volts (all (4) batteries in combination).

• 

If the hand held transmitter batteries measure less than 5.3 volts all (4) batteries in combination).

• 

TROUBLE SHOOTING

If you encounter problems with your fireplace system, the problem may be with either the fireplace itself or with the 

remote.  Review the fireplace manufacturer’s operation manual to make sure all connections are properly made.  Then 

check the operation of the remote in the following manner:

Make sure all batteries are correctly installed in the transmitter and receiver. Also check that the batteries are fully 

• 

charged.

Check batteries in transmitter to ensure contacts are touching (+) and (-) ends of battery. Bend metal contacts in for 

• 

tighter fit.

Be sure receiver and transmitter is within 20 to 25-foot operating range.

• 

Keep receiver from temperatures exceeding 130º F. Battery life will be shortened if exposed to high temperatures.

• 

If receiver is installed in a tightly enclosed metal surrounding, the operating distance will be shortened.

• 

Make sure the hand-held transmitter and remote receiver are communicating properly (see LEARNING 

• 

       TRANSMITTER TO RECEIVER section).

FCC REQUIREMENTS

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODI-

FICATIONS TO THE EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT

P/N 900259-00 Rev. A

HOW TO REGISTER A CLAIM AGAINST WARRANTY

In order for any claim under this warranty to be valid, you must contact the IHP dealer/distributor from which you 

purchased the product.  If you cannot locate the dealer/distributor, then you must notify IHP in writing.  IHP must be 

notified of the claimed defect in writing within 90 days of the date of failure.  Notices should be directed to the IHP 

Warranty Department at 1508 Elm Hill Pike, Suite 108; Nashville, TN 37210 or visit our 

website at www.IHP.us.com

Summary of Contents for RC-S-TOUCH









Reviews: