IHP GA9050A-1 Installation Instructions Manual Download Page 5

IHP.US.com

126905-01_B

5

GA9050A-1 SERIES ON/OFF SAFETY VALVE/PILOT KIT ASSEMBLY

Natural Gas Installation

1.  Thread the gas control valve onto the burner inlet fitting (see 

Figure 7). Use thread sealant on the male threads of the burner 

inlet fitting. Hold the burner inlet fitting with a wrench to prevent 

overtightening the connection to the burner. Make sure the control 

rod is facing the front (see Figure 7).

2.  Attach the pilot gas line to the pilot outlet of the gas control valve 

and tighten. Connect the thermocouple to the rear of the gas 

control valve. See Figure 8. Do not overtighten. If using propane/

LP gas, see

 Changing Pilot Orifice

, page 6.

3.  Install the inlet fitting into the inlet opening of the gas control valve 

(see Figure 9). Use thread sealant on the male pipe threads.

4.  Place the burner pan assembly in the center of the fireplace floor. 

Make sure the front of pan faces forward.

Figure 7 - Installing Gas Control Valve

Figure 8 - Gas Control Valve with Thermocouple and Pilot 

Burner Inlet Fitting 

(containing orifice)

Gas Control Valve

Burner Pan 

Assembly

Control 

Rod

Thermocouple and 

Line

Pilot and Line

Gas Control Valve

Pilot Flow 

Adjustment Screw

Figure 9 - Installing Inlet Fitting and Gas Connector Tube 

Gas Control Valve

Gas Inlet 
Fitting

Gas Connector 
Tube

Inlet Opening

INSTALLATION  

Continued

Figure 10 - Installing Cover, Control Knob, and Piezo Ignitor

Piezo 

Ignitor

Control Rod 
Extension

Screw

Valve 

Cover

Control 

Knob

Thermocouple

Ignitor

Pilot

5.  Thread the gas supply adaptor to the fireplace gas supply pipe. 

Adjust to most convenient position.

6.  Install the gas connector tube to the gas supply adaptor. Carefully 

shape tube and attach to gas inlet fitting (see Figure 9). Be careful 

not to cause kinks in tube.

7.  Test for leaks following instructions in your hearth kit owner’s 

manual under the section 

Testing Burner for Leaks

.

8.  Retighten and adjust the location of the gas control as necessary. 

The gas control should be level, with the control rod to the front. 

9.  Install cover to burner pan using screws provided.
10. Install thermocouple, pilot, and ignitor onto valve cover as shown 

in Figure 10. Use the provided screws. 

11. Push the control rod extension onto the “D” shaped control rod 

through the center hole in the cover.

12. Install the position decal and control knob making sure to align 

the marks with the correct stop positions of the gas control. Pilot 

position will allow the knob to push in about 1/2". Align the decals 

in the pilot position. 

f i r e - p a r t s . c o m

Summary of Contents for GA9050A-1









Reviews: