background image

6

PRODUCT FEATURES

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system.

The ODS/pilot shuts off the heater if there is not enough fresh air and cuts off main burner gas in the 

event of flame out.

ELECTRONIC PUSH BUTTON IGNITION SYSTEM

This heater is equipped with an electronic push button ignition system. This system requires

one AAA battery (provided).

LEG KIT

2 legs and 4 mounting screws are included for floor mounting the heater.  See page 13.

PIEZO IGNITION SYSTEM (SELECT MODELS)

This heater is equipped with a piezo electric ignition system.

THERMOSTAT HEAT CONTROL(SELECT MODELS)

The control automatically cycles the burner on and off to maintain a desired room

temperature. See page 24.

FAN KIT(SELECT MODELS)

The fan kit helps to distribute the warmed air into the space more rapidly.

  State of Massachusetts: 

The installation must be made by a licensed plumber or gas fitter in 

  the Commonwealth of Massachusetts. Sellers of unvented propane or natural gas-fired 

  supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale 

  of the unit.

  In the State of Massachusetts, unvented propane or natural gas-fired space heaters shall 

  be prohibited in bedrooms and bathrooms.

  In the State of Massachusetts the gas cock must be a T-handle type. The State of 

  Massachusetts requires that a flexible appliance connector cannot exceed three feet

  in length.

LOCAL CODES

Install and use heater with care. The installation must conform with local codes or, in the absence of 

local codes, with the latest edition of The Nation Fuel Gas Code, ANSI Z223.1/NFPA 54

*Available from:

American National Standard Institute, Inc. 

 National Fire Protection Association, Inc.

1430 Broadway  

 

 

 

 

1 Batterymarch Park

New York, NY 10018  

 

 

 

Quincy, MA 02269-9101

This heater is designed for vent-free operation. State and local codes in some areas prohibit, restrict 

and or have special requirements for vent-free heaters.

Summary of Contents for (C)(GC)IR6PMA series





























Reviews: