background image

Safety Instructions, Protective Measures and Guidelines 

D8-1_EN 

– V1.0 

4/14 

1.4 

Safety Instructions 

1.4.1 

Classification of Information 

The degree and type of hazard are assigned to one of the following classes. 

 

DANGER! 

Safety instructions marked with 

DANGER

 indicate an imminently hazardous situation. 

A disregard of the notice 

inevitably

 leads to a 

serious or even fatal accident

 

 

WARNING! 

Safety instructions marked with 

WARNING

 indicate a potential hazardous situation. 

Failure to observe this notice is 

likely

 to result in a 

serious or fatal accident

 or 

property damage

 

 

CAUTION! 

Safety instructions marked with 

CAUTION

 indicate potential danger. 

Failure to comply with the notice may 

possibly

 result in an 

accident

 or 

property damage

 

 

NOTE 

Safety instructions marked with 

NOTE

 indicate a potential hazardous situation. 

Disregard of the notice may 

possibly

 result in 

property damage

1.5 

Electromagnetic Compatibility 

 

WARNING! 

 

Risk of injury due to interference with signals and devices 

Disturbed signals can cause unforeseen device reactions. Carry out the wiring in accordance with the EMC measures. 
Failure to follow these instructions can result in death, serious injury, or material damage 

 

 

Measures for EMC 

Effect 

Device assembly 

Use cable clamps for the shield support, 
connect metal parts over a large area. 

Good conductivity due to surface contact. 

Switching devices such as contactors, relays 
or solenoid valves with interference 
suppression units or spark suppressors (e.g. 
diodes, varistors, RC elements) 

Reduce mutual interference couplings. 

Wiring 

Keep cables as short as possible. 

Avoid capacitive and inductive interference. 

 

 

Summary of Contents for motion Plastics D8-1















Reviews: