Quick Start Guide
– 3 –
Safety and Regulatory Information
FCC Class A
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void your authority to
operate the equipment.
You may use unshielded twisted-pair (UTP) for RJ-45 connections -
Category 3 or better for 10 Mbps connections, Category 5 or better for
100 Mbps connections, Category 5, 5e, or 6 for 1000 Mbps connections.
For fiber optic connections, you may use 50/125 or 62.5/125 micron
multimode fiber or 9/125 micron single-mode fiber.
CE Mark
CE Mark Declaration of Conformance for EMI and Safety (EEC)
This information technology equipment complies with the requirements
of the Council Directive 2004/108/EC on the Approximation of the laws
of the Member States relating to Electromagnetic Compatibility and
2006/95/EC for electrical equipment used within certain voltage limits
and the Amendment Directive 93/68/EEC. For the evaluation of the
compliance with these Directives, the following standards were applied:
RFI Emission:
◆
Limit according to EN 55032:2012+AC:2013, Class A
◆
Limit for harmonic current emission according to EN 61000-3-
2:2014, Class A
◆
Limitation of voltage fluctuation and flicker in low-voltage supply
system according to EN 61000-3-3:2013
Immunity:
◆
Product family standard according to EN 55024:2010+A1:2015
◆
Electrostatic Discharge according to IEC 61000-4-2:2008 ED. 2.0
◆
Radio-frequency electromagnetic field according to IEC 61000-4-
3:2010 ED 3.2
◆
Electrical fast transient/burst according to IEC 61000-4-4:2012 ED.
3.0
◆
Surge immunity test according to IEC 61000-4-5:2014 ED. 3.0
◆
Immunity to conducted disturbances, Induced by radio-frequency
fields: IEC 61000-4-6:2013 ED. 4.0
◆
Power frequency magnetic field immunity test according to IEC
61000-4-8:2009 ED. 2.0
◆
Voltage dips, short interruptions and voltage variations immunity
test according to IEC 61000-4-11:2004 ED. 2.0
LVD:
◆
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + A2: 2013
The Declaration of Conformity (DoC) can be obtained from
www.ignitenet.com/support.
Laser Safety
Warning:
Fiber Optic Port Safety:
Avertissment:
Ports pour fibres optiques - sécurité sur le plan optique
:
Warnhinweis:
Faseroptikanschlüsse - Optische Sicherheit:
Power Cord Safety
Please read the following safety information carefully before installing
the switch:
Warning
: Installation and removal of the unit must be carried out by
qualified personnel only.
◆
The unit must be connected to an earthed (grounded) outlet to
comply with international safety standards.
◆
Do not connect the unit to an A.C. outlet (power supply) without an
earth (ground) connection.
◆
The appliance coupler (the connector to the unit and not the wall
plug) must have a configuration for mating with an EN 60320/IEC
320 appliance inlet.
◆
The socket outlet must be near to the unit and easily accessible. You
can only remove power from the unit by disconnecting the power
cord from the outlet.
◆
This unit operates under SELV (Safety Extra Low Voltage) conditions
according to IEC 60950. The conditions are only maintained if the
equipment to which it is connected also operates under SELV
conditions.
France and Peru only
This unit cannot be powered from IT† supplies. If your supplies are of IT
type, this unit must be powered by 230 V (2P+T) via an isolation
transformer ratio 1:1, with the secondary connection point labelled
Neutral, connected directly to earth (ground).
† Impédance à la terre
Important!
Before making connections, make sure you have the correct
cord set. Check it (read the label on the cable) against the following:
When using a fiber optic port, never look at the
transmit laser while it is powered on. Also, never look
directly at the fiber TX port and fiber cable ends when
they are powered on.
Ne regardez jamais le laser tant qu'il est sous tension.
Ne regardez jamais directement le port TX
(Transmission) à fibres optiques et les embouts de
câbles à fibres optiques tant qu'ils sont sous tension.
Niemals ein Übertragungslaser betrachten, während
dieses eingeschaltet ist. Niemals direkt auf den Faser-
TX-Anschluß und auf die Faserkabelenden schauen,
während diese eingeschaltet sind.
CLASS 1
LASER PRODUCT
PRODUIT LASER
DE CLASSE 1
LASERPRODUKT
DER KLASSE 1
