background image

 

REFRIGERATION LTD 

 

Refrigerated Pastry Display Case

 

| www.igloorefrigeration.com

 

 

4.  UNIT START UP 

The temperature of the cooled space and aggregate operating cycle may fluctuate. This depends on numerous 
factors, such as the amount and temperature of products placed in the device and temperature of the surroundings.  
The  equipment should be placed in a dry and well-ventilated place, ensuring proper air exchange (distance 
between the wall and the equipment– min. 10cm), out of sunlight, kept far from heat sources and devices enforcing 
air flow (ceiling and portable ventilators, blow-in heaters). The equipment functions properly in a room, where 
temperature falls within appropriate climatic class. The operation of the equipment may worsen when operates 
outside the stated temperature range. 

 

    

**** Place products evenly in the center of the rotating shelf, to keep the balance even **** 

 

DO NOT BLOCK VENTILATION HOLES!!! Minimal distance between ventilation holes of 
the device and other elements of the equipment (furniture) or walls should equal at 
least about 10 cm. 

 

                        

 

 

Figure 6 Ventilation holes of the device 

 

Summary of Contents for JOR Series

















Reviews: