en
13
User manual Basia 2, Tobi
www.igloo.pl
2.3. Technical data
Table 1 Technical data
Name of the
device
Rated volta
-
ge [V/Hz]
Rated
current [A]
Rated ligh
-
ting power
[W]
Electric
energy con
-
sumption
[kWh/24h]
Cooled sur
-
face [m2]
Usable sur
-
face [dm3]
Weight of
the device
[kg]
Aruba 1.25
230/50
6,5
30
18,1
0,85
112
300
Aruba 2.5
230/50
13
60
36,4
1,7
224
520
Aruba 2/1.0
230/50
3,3
18
9,4
0,44
62
195
Aruba 2/1.25
230/50
5,8
30
16,3
0,6
92
245
3. PREPARING THE DEVICE FOR EXPLOITATION
3.1. Requirements concerning the place of installation
• Verify whether the cross section of feeding conduits is proper for power consumption of the installed device.
• It is forbidden to connect the device by extension rods or dividers.
• The device should be connected to the separate, properly made electric circuit with plug-in socket with protecting pin
(according to PBUE /Regulations concerning Electric Equipment Construction/)
The device may be actuated solely after confirmation of the fire protection efficiency with results of measu
-
res performed according to binding regulations!
3.2. Connection and actuation
• Unpack the device and remove the wooden platform from the basis Fig.4 (p.8)
• The device should be placed on an even and on a sufficiently hard base, and then level it with the help of levelling feet.
• Remove the protection foil from the elements of the device
• Clean the whole device with water, of temperature not exceeding 40ºC with addition of washing liquid.
Do not use surface
scratching agents, caustic agents or agents containing chlorine and/or soda!
Do not use water stream to clean the device, only a wet cloth
• If the user shall obtain a device partially disassembled to secure it during transportation, perform the following ope
-
rations:
1. Place cross-bars under VGN containers Fig.5/5 (p.8)
2. Place VGN containers according to Fig.2 (p.5) or Fig.3 (p.6)
3. Slide in glass sides according to Fig.5/2 (p.8)
4. Mount front screen Fig.6 (p.9)
After installing the device in the final location it should be left to rest for at least 2 hours before the
actuation, to allow the cooling agent level to settle, which will prevent from problems with actuating
the cooling aggregate!
WARNING: Protect the cooling circuit against damage!
• Place the plug of the connecting cable directly in plug-in socket (it is forbidden to connect the device by means of
extension cords or dividers!)
Power sockets (optional) may be used to power cash register, weight, and similar receivers with
power not exceeding 500W!
• Turn on the main switch Fig.7/2 (p.9), which activates the temperature regulator, and then aggregate of the device
• Set the temperature on thermostat control panel Fig.7/1 (p.9) (service details on p.18 or 19)
• Turn on the lighting switch Fig.7/3 (p.9)
Summary of Contents for Aruba 1.25
Page 41: ...ru 41 Basia 2 Tobi www igloo pl 4 10 2 1 2 4 1 Igloo Carel 7 51 52...
Page 42: ...ru 42 Basia 2 Tobi www igloo pl 8 48 13 5 5 1 11 48 3 2 1 1 2 3 11 1 2 3 12 1 2 3...
Page 43: ...ru 43 Basia 2 Tobi www igloo pl 15 21 6 6 1 230 50 Igloo 25 C 1 2 3 4 14 1 2 3 4...
Page 45: ...ru 45 Basia 2 Tobi www igloo pl 3 3 2 www igloo pl 1 2 3 4 5 6 7 7 1 IGLOO 16 Igloo...
