iGGUAL PSIMS200 User Manual Download Page 8

1. 

The remote control can be IR Type or RF Type.

2.

 (A-IR Type) Plug in the power cable for the controller. the power source indicator will flash. After the stop button of the remote control is pressed and either the up 

or down button is pressed again, the power relay of the controller will start to operate. Press the stop button after eight seconds, the power source indicator will stop 
flashing. This is evidence that the controller has finished automatic learning successfully. Above operation is normally completed in eight seconds.
(B-RF Type). Press the down button, then plug in the power source indicator will flash . After the stop button of the remote control is pressed. The down button is 
pressed again,the power relay of the controller will start to operate. Press the stop button, after eight seconds. the power source indicator will stop flashing. This is 
evidence that the controller has finished automaticlearningsuccessfully,Above operation is normally completed in eight seconds.

3. 

When the up and down buttons are pressed in the same time, the remote control is locked. Operation will be stopped. The system will be unlocked if the stop button 

is pressed again.

4.

 The power source will be cut off automatically if the motor operation has passed the preset time limit. Then the motor will stop operation .

5.

 The motor will perform up functions if the up button of the controller is pressed. If the stop button or down button is pressed, the motor will stop operation. When 

down button is pressed again, the motor will perform down functions. ln case stop or up button is pressed, the motor will stop operation.

6. Remote control system

1. Structure

2. Installing

Moving Parts of the drive must be installed higher than 2,5 mm above above the floor or other level that could provide access to it Choose a suitable place for 
installing.it is best to install two screws on the wall, the distance of the screwsust be equal to that of the two rings and they should be at the same level, the rings 
must be strong enough to loading more than 25kg weights.

3. Useful instructions

Hold the pulling ring tightly and pull down the screen slowly, then stop when the black border comes out(or stop pulling where you want to stop), the screen can be 
auto-fixed. if it can not be fixed, please operate it once again according to the same method. After using.release the screen and it will go up and back to the housing.

4. Warnings

a. 

The screen can not be folded.Do not use fingers or hard objects to touch the screen surface.Do not splash the milk, fruit juice or other chemical doses to the screen 

surface. Keep the screen far away from the high temperature objects or fire.

b.

 If the screen is dirty wash the screen gently by a broom or a cotton ball do not use the organic solvents to clean the screen surface.

c.

 When pulling the screen down, must be slowly and vertical. Do not pull it roughly, please stop pulling as soon as the black border is out or the screen is jammed or 

injured, then send the screen to the maintenance center.

d.

 After using, put the screen back to the housing in order to avoid being polluted, If not using it for a long time,please take the screen from the wall and pack it in a 

carton.

WALL-MOUNTED MANUAL SCREEN 

English

Projection Screen. User Manual

CONNECT & ENJOY

®

Summary of Contents for PSIMS200













Reviews: