IFM ZZ0814 Instructions For Setup Download Page 25

Page: 25 / 36

ZZ0814 ZZ0815 ZZ0816 ZZ0817

•

[O3D Sensor]: Detects the loading direction using the O3D354.

•

[Light Barrier]: Detects the loading direction using the 2x OGP700.

[Signal Lamp]

Sets the signal lamp. Possible settings:

•

[Activate]: Activates the signal lamp.

•

[Deactivate]: Deactivates the signal lamp.

•

[Time]: Sets the active time of the signal lamp.

[Buzzer]

Sets the Buzzer. The buzzer can generate acoustic signals. Possible settings:

•

[Activate]: Activates the buzzer.

•

[Deactivate]: Deactivates the buzzer.

•

[Time]: Sets the active time of the buzzer.

[Gate Action]

Sets the selected Gate. Possible settings:

•

[Activate]: Activates the gate. ID tags are detected.

•

[Deactivate]: Deactivates the gate. The tags are not detected.

[Reset]

The [Reset] button resets the gate configuration to the default settings.

[Test Mode]

The [Test Mode] button changes to Test Mode. (

Test mode

25)

[Go to Monitor]

The [Go to Monitor] button switches to monitor mode. (

Monitor mode

26)

8.4.2 Test mode

The [Test Mode] recognises ID tags with the connected RFID read/write heads and displays the data
they contain. No configuration is required for the [Test Mode]. No feedback files are generated, and no
result files are queried.

Fig. 12: Test mode of the Gates software

[Reset Reading]

The [Reset Reading] button resets the table. Afterwards, ID tags can be detected again.

[Back]

The [Back] button switches back to the gates configuration. (

Gate configuration

24)

Summary of Contents for ZZ0814





































Search results

Summary of Contents for ZZ0814

Reviews:

Related manuals for ZZ0814

Brands by name

Popular brands

IFM ZZ0814, Instructions For Setup

Search results

Summary of Contents for ZZ0814

Reviews:

Related manuals for ZZ0814

Brands by name

Popular brands