background image

4

•  The manufacturer assumes no liability or warranty for any consequences 

caused by tampering with the product or incorrect use by the operator�

•  Installation, electrical connection, set-up, operation and maintenance of the 

product must be carried out by qualified personnel authorised by the machine 

operator�

•  Protect units and cables against damage�

3  Getting started

The unit can be used without any further parameter setting with the settings 

described under 

→ 14 Factory setting

If necessary, the factory setting can be changed via the IO-Link interface: 

 

Connect unit to PC to set the parameters via the IO-Link interface�

 

Set the standard unit of measurement�

 -[Uni]: °C or °F

 

Set the analogue signal�

 -[OU2]: I = 4���20 mA or Ineg = 20���4 mA or OFF = output off
 -[ASP] and [AEP]: Scaling of the measuring range�

 

Configure the analogue signal for the alarm�

 -[FOU2]: On = 21�5 mA or OFF = 3�5 mA

 

Set the calibration check limit�

 -[ccL]: Temperature deviation from which the unit provides a warning�

 

Configure the switching logic for the alarm and the warning of the diagnostic 

output�

 -[P-n]: PnP or nPn

 

Activate / deactivate the LED at the head of the unit�

 -[LED]: ON = LED is on (green, blue, red) or OFF = LED off or Notification = 

LED on for warnings and alarms only 

 

Finish parameter setting, install 

(→ 6)

, connect 

(→ 8)

 and set  up the unit

4  Functions and features

The unit detects the medium temperature and provides the measured value via an 

analogue and/or a digital signal�

Summary of Contents for TCC5 Series






















Reviews: