background image

24

10.1.1  Switching between the menu levels

Change to the 

submenu

Switching to the next submenu via the parameters [EF], [CFG], 

[MEM], [EPD] or [SIM]�

 

► Select a submenu with [▲] or [▼] and switch to the submenu 

by pressing [Enter]�

Back to the process 

value display

 

► Wait for 30 seconds

or

 

► Change from the submenu to the main menu, from the main 

menu to the process value display with [▲] or [▼].

10.1.2  Locking / unlocking

The unit can be locked electronically to prevent unintentional settings� On delivery: 

not locked�
Locking is also possible via an IO-Link capable parameter setting tool�

Locking

 

► Make sure that the unit is in the normal operating mode�

 

► Press [▲] and [▼] simultaneously for 10 s.

 

> [Loc] is displayed�

During operation: [Loc] is briefly displayed if you try to 

change parameter values�

Unlocking

 

► Press [▲] and [▼] simultaneously for 10 s.

 

> [uLoc] is displayed�

10.1.3  Timeout

If no button is pressed for 30 s during parameter setting, the unit returns to the 

operating mode with unchanged parameter�

10.2  Setting the analogue value for temperature

 

► Select [ASP1] and set the value at which the minimum value is provided�

 

► Select [AEP1] and set the value at which the maximum value is pro-

vided�

10.3  Setting the analogue value for volumetric flow

 

► Select [ASP2] and set the value at which the minimum value is provided�

 

► Select [AEP2] and set the value at which the maximum value is pro-

vided�

Summary of Contents for SM9x04 Series
































Reviews: