background image

12

8.2  Menu explanation

SP1/rP1

Maximum / minimum value for system pressure, at which output 1 changes 

its switching status�

OU1

Output function for OUT1:

• Switching signal for the limit values: hysteresis function [H ��] or window 

function [F ��], normally open [� no] or normally closed [� nc] each�

OU2

Output function for OUT2:

• Switching signal for the limit values: hysteresis function [H ��] or window 

function [F ��], normally open [� no] or normally closed [� nc] each��

• Analogue signal for the current system pressure: 4���20 mA [I], 0���10 V [U]�

SP2/rP2

Maximum / minimum value for system pressure, at which output 2 changes 

its switching status�

ASP

Analogue start point for the system pressure: measured value at which 

4 mA / 0 V are output�

AEP

Analogue end point for the system pressure: measured value at which 

20 mA / 10 V are output�

EF

Extended functions / Opening menu level 2�

HI

Maximum value memory for the system pressure�

LO

Minimum value memory for the system pressure�

COF

Zero point calibration�

CAr

Calibration reset�

dS1/dS2

Switch-on delay for OUT1/OUT2�

dr1/dr2

Reset delay for OUT1/OUT2�

P-n

Output polarity: pnp / npn

dAP

Damping for the switching outputs�

dAA

Damping for the analogue signal�

diS

Update rate and orientation of the display�

Uni

Standard unit of measurement for the system pressure�

Summary of Contents for PF295 Series


















Reviews: