background image

11

UK

10  Operation

After every power on all LEDs light and go out again step by step (during this time 

the output is closed if configured as normally open)� The unit is then ready for 

operation�
In case of power failure or interruption all settings remain�

Operating indicators 

         

Green LED bar: Current flow within the represen-

tation range�

Indication of the switch point (SP):

- LED orange: output closed�

- LED red: output open�

         

LED 9 flashes: current flow above the

representation range�

         

LED 0 flashes: current flow far below the represen-

tation range�

Interference indicator

         

         

Short circuit at the switching output:

The operating indicator and red LEDs light 

alternately� 

If the short circuit has been rectified, the unit imme-

diately passes into the normal operating state�

The current operating state is displayed�

Display OFF

(no LED lights):

Operating voltage too low (< 19 V) or failed�

Ensure a correct voltage supply�

11  Maintenance

Recommended maintenance: 

 

► Check the sensor tip for build-up from time to time� 

 

► Clean it using a soft cloth� Stubborn build-up (e�g� lime) can be removed using 

a common vinegar cleaning agent�

Summary of Contents for efector 300 SI5010














Reviews: