background image

Ethernet camera O2M113

4

2 Safety instructions

2.1. General

These instructions are part of the device . It contains information and illustrations 

about the correct handling of the device and must be read before installation or 

use
Observe the operating instructions . Non-observance of the instructions, operation 

which is not in accordance with use as prescribed below, wrong installation or 

incorrect handling can seriously affect the safety of people and machinery .

2.2 Target group

These instructions are intended for authorised persons according to the EMC and 

low-voltage directives . The device must only be installed, connected and put into 

operation by a qualified electrician .

2.3 Electrical connection

Disconnect the device externally before handling it . If necessary, also disconnect 

any independently supplied output load circuits .
If the device is not supplied by the mobile on-board system (12/24 V battery 

operation), it must be ensured that the external voltage is generated and supplied 

according to the criteria for safety extra-low voltage (SELV) as this voltage is 

supplied without further measures to the connected controller, the sensors and the 

actuators .
The wiring of all signals in connection with the SELV circuit of the device must also 

comply with the SELV criteria (safety extra-low voltage, safe electrical separation 

from other electric circuits) .
If the supplied SELV voltage is externally grounded (SELV becomes PELV), the 

responsibility lies with the user and the respective national installation regulations 

must be complied with . All statements in this document refer to the device the 

SELV voltage of which is not grounded .
The connection terminals may only be supplied with the signals indicated in the 

technical data and/or on the device label and only the approved accessories of ifm 

electronic gmbh may be connected .

2.4 Tampering with the unit

In case of malfunctions or uncertainties please contact the manufacturer . 

Tampering with the unit can seriously affect the safety of operators and machinery . 

It is not permitted and leads to the exclusion of any liability and warranty claims .

Summary of Contents for Efector 250 O2M113




















Reviews: