background image

CANwireless

CR3133

9

7 Light indicators

2

1

1:

ON LED

2:

STATUS LED

7.1 ON LED

Colour

State

Meaning

-

Off

The device is switched off or in sleep mode.

Green

Flashing slowly

The device is in update mode and ready to receive a
firmware update.

The ON and STATUS LEDs flash simultaneously.

Green

Flashing quickly

Firmware is being installed.

The ON and STATUS LEDs flash simultaneously.

Green

On

The device is switched on.

Terminal 30 voltage is in the permissible range.

Red

On

The device is switched on.

Terminal 30 voltage is outside the permissible range.

Orange

On

The device is reset to factory settings.

The ON and STATUS LEDs are lit simultaneously.

Turquoise

On

The radio module is being updated (via HTTP server).

The ON and STATUS LEDs are lit simultaneously.

Magenta

On

Active connection with CANwireless configurator

The ON and STATUS LEDs are lit simultaneously.

Tab. 1: ON LED

7.2 STATUS LED

The STATUS LED indicates the operating status of the active connection.

Colour

State

Meaning

-

Off

The device is switched off or in sleep mode.

Green

Flashes (200 ms on, 200 ms off, 200
ms on, 1000 ms off)

The device is initializing.

Green

Flashes (200 ms on, 200 ms off)

The device is ready for connection.

Green

On

The device has established a connection.

The device functions reliably.

Summary of Contents for CR3133























Reviews: