IFM Electronic SM2000 Operating Instructions Manual Download Page 30 | Manualshive

Page: 30 / 44

background image

30

9 Set-up

After power on and expiry of the power-on delay time (approx� 5 seconds) the unit

is in the normal operating mode� It carries out its measurement and evaluation

functions and generates output signals according to the set parameters�

•

During the power-on delay time the outputs are switched as programmed:

-ON with normally open function (Hno / Fno)
-OFF with normally closed function (Hnc / Fnc)�

•

If output 2 is configured as analogue output, the output signal is at 20 mA (cur-

rent output) or 10 V (voltage output)�

10 Parameter setting

Parameters can be set before installation and set-up of the unit or during opera-

tion�

If you change parameters during operation, this will influence the function�

►

Ensure that there will be no malfunctions in your plant�

During parameter setting the unit remains in the operating mode� It continues to

monitor with the existing parameter until the parameter setting has been com-

pleted�

10.1 IO-Link interface

Using an IO-Link capable parameter setting tool, the following options are avail-

able:

-Reading current process values�
-Reading, changing and saving current parameter settings and transmitting

them to other units of the same type�

The IO-Link Device Description (IODD) can be downloaded at

www�ifm�com/uk/io-link�

«
...
28
29
30
31
32
...
»

Summary of Contents for SM2000













































Reviews:

No comments

Related manuals for SM2000

Brand: Kane Pages: 16

Brand: Bacharach Pages: 48

Brand: Bacharach Pages: 24

Brand: Macnaught Pages: 14

Brand: Bartington Pages: 15

Brand: Bartec Pages: 216

Brand: YOKOGAWA Pages: 2

Brand: Harley Benton Pages: 28

Brand: J.P. Instruments Pages: 9

Brand: J.ASSY Pages: 13

Brand: NCTE Pages: 10

Brand: S+S Regeltechnik Pages: 32

Intelligizer Fence Monitor

Brand: Zareba Pages: 8

Celviano AP-60R

Brand: Casio Pages: 44

Brand: Ditel Pages: 2

Brand: horiba Pages: 103

Brand: Kathrein Pages: 24

Brand: Icel Manaus Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands