manualshive.com logo in svg

IFM Electronic Efector 300, Operating Instructions Manual, Page: 28 / 31

Share
Download
IFM Electronic Efector 300 Operating Instructions Manual Download Page 28

28

11  Operation

11.1  Reading the process value

The LEDs 1-6 signal which process value is currently displayed�  

The process value to be displayed as standard (temperature, flow velocity) can 

be preset. → 10.5.3 Configuration of the standard display. A standard unit of 

measurement can be defined for the flow velocity (l/min, m

3

/h, gpm or gph) → 

10�5�2)� For temperature measurement, °C or °F can be selected as standard unit 

of measurement (→ 10.5.1).
Further process values can be read in addition to the preset standard display:

 

► Press the buttons 

[▲]

 or

 [▼]

�

 

> The LED of the selected process value display is lit and the current process 

value is displayed�

 

> After 30 seconds the display changes to the standard display�

LED Process value display

Unit

1

Current flow volume per minute

l / min

2

Current flow volume per hour

m

3

 / h

3

Current flow volume per minute

gal / min

4

Current flow volume per hour

gal / h

5

Current medium temperature

°C

6

Current medium temperature

°F

7

Current flow volume in 10

3

11.2  Reading the parameter value

Take the following steps to display the currently set parameter value:

Summary of Contents for Efector 300
































Reviews:

No comments