iFIT NORDICTRACK COMMERCIAL STUDIO CYCLE S10i User Manual Download Page 3

3

IMPORTANT PRECAUTIONS

    WARNING:

 To reduce the risk of serious injury, read all important precautions and 

instructions in this manual and all warnings on your studio cycle before using your studio cycle. iFIT 
assumes no responsibility for personal injury or property damage sustained by or through the use of 
this product.

1.  It is the responsibility of the owner to ensure 

that all users of the studio cycle are ade-
quately informed of all precautions. 

2.  Keep children under age 16 and pets away 

from the studio cycle at all times.

3.  Consult your health care provider before 

beginning any exercise program. This is 
especially important for persons over age 35 
or persons with pre-existing health problems.

4.  Consult your health care provider before 

beginning or continuing any exercise pro-
gram during pregnancy. Use the studio 
cycle only as authorized by your health care 
provider.

5.  The studio cycle is not intended for use by 

persons with reduced physical, sensory, or 
mental capabilities or lack of experience and 
knowledge, unless they are given supervi-
sion or instruction about the use of the 
studio cycle by someone responsible for 
their safety.

6.  Use the studio cycle only as described in this 

manual.

7.  The studio cycle is intended for home use 

only. Do not use the studio cycle in a com-
mercial, rental, or institutional setting.

8.  Keep the studio cycle indoors, away from 

moisture and dust. Do not put the studio 
cycle in a garage or covered patio, or near 
water.

9.  Place the studio cycle on a level surface, 

with a mat beneath it to protect the floor or 
carpet. Make sure that there is at least 2 ft. 
(0.6 m) of clearance around the studio cycle. 

10. Inspect and properly tighten all parts each 

time the studio cycle is used. Replace 
any worn parts immediately. Use only 
manufacturer-supplied parts.

11. Always plug the power adapter into the 

studio cycle before you plug it into an outlet.

12. The studio cycle should not be used by 

persons weighing more than 350 lbs. 
(160 kg).

13. Wear appropriate clothes while exercising; 

do not wear loose clothes that could become 
caught on the studio cycle. Always wear ath-
letic shoes for foot protection.

14. Be careful when mounting and dismounting 

the studio cycle.

15. Always keep your back straight while using 

the studio cycle; do not arch your back.

16. The studio cycle does not have a freewheel; 

the pedals will continue to move until the 
flywheel stops. Reduce your pedaling speed 
in a controlled way.

17. To stop the flywheel quickly, press the brake 

knob downward.

18. When the studio cycle is not in use, press the 

brake knob downward and tighten it firmly.

19. Over exercising may result in serious injury 

or death. If you feel faint, if you become short 
of breath, or if you experience pain while 
exercising, stop immediately and cool down.

Summary of Contents for NORDICTRACK COMMERCIAL STUDIO CYCLE S10i









































Reviews: