IEI Technology SPCIE-C2260-i2 Page 74 User Manual Download

Page: 74 / 162

SPCIE-C2260-i2 PICMG 1.3 CPU Card

Page 58

4.3.3 Flash Descriptor Security Override Jumper

The Flash Descriptor Security Override jumper (J_FLASH1) allows to enable or disable

the ME firmware update. Refer to

Figure 4-9

and

Table 4-2

for the jumper location and

settings.

Setting

Description

Short 1-2

Disabled (default)

Short 2-3

Enabled

Table 4-2: Flash Descriptor Security Override Jumper Settings

Figure 4-9: Flash Descriptor Security Override Jumper Location

To update the ME firmware, please follow the steps below.

Step 1:

Before turning on the system power, short pin 2-3 of the Flash Descriptor

Security Override jumper.

Step 2:

Update the BIOS and ME firmware, and then turn off the system power.

Step 3:

Remove the metal clip on the Flash Descriptor Security Override jumper or

return to its default setting (short pin 1-2).

Step 4:

Restart the system. The system will reboot 2 ~ 3 times to complete the ME

firmware update.

Step 0:

Summary of Contents for SPCIE-C2260-i2



































































































































































Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands

IEI Technology SPCIE-C2260-i2, User Manual

Search results

Summary of Contents for SPCIE-C2260-i2

Reviews:

Related manuals for SPCIE-C2260-i2

Brands by name

Popular brands