background image

12 

DECLARATION OF CONFORMITY 

 

This equipment is in conformity with the following EU directives:   

 

EMC Directive (2004/108/EC, 2014/30/EU) 

 

Low-Voltage Directive (2006/95/EC, 2014/35/EU) 

 

RoHS II Directive (2011/65/EU, 2015/863/EU) 

 

Medical Device Directive 93/42/EEC: EN 60601-1 

 

If the user modifies and/or install other devices in the equipment, the CE 

conformity declaration may no longer apply. 

If this equipment has telecommunications functionality, it also complies 

with the requirements of the Radio Equipment Directive 2014/53/EU. 

IEI Integration Corp declares that this equipment is in compliance with the 

essential requirements and other relevant provisions of Directive 

2014/53/EU. 

 

 

FCC WARNING 

 

This equipment complies with part 18 of the FCC Rules. 

This equipment generates, uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, 

the user is encouraged to try to correct the interference by one or more of 

the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that 

to which the receiver is connected. 

 

 

 

Summary of Contents for POCm-W22C-ULT3





















Reviews: