IEI Technology PCISA-BT User Manual Download Page 33

Page: 33 / 135

PCISA-BT CPU Card

Page 19

The ATX power supply enabled connector enables the PCISA-BT to be connected to an

ATX power supply. Refer to

Table 3-4

for the configuration of AT/ATX power mode.

Figure 3-2: ATX Power Supply Enabled Connector Location

Pin

Description

GND

PS_ON#

5VSB

Table 3-3: ATX Power Supply Enabled Connector Pinouts

The AT/ATX power mode settings are listed below.

Setting

Description

AT Power Mode

Short 1-2 (Default)

ATX Power Mode

Connect PS_ON# and 5VSB cable from ATX power supply

Table 3-4: AT/ATX Power Mode Setting

3.2.2 Audio Connector

CN Label:

J_AUDIO1

CN Type:

10-pin header, p=2 mm

CN Location:

See

Figure 3-3

CN Pinouts:

See

Table 3-5

Summary of Contents for PCISA-BT








































































































































Search results

Summary of Contents for PCISA-BT

Reviews:

Related manuals for PCISA-BT

Brands by name

Popular brands

IEI Technology PCISA-BT, User Manual

Search results

Summary of Contents for PCISA-BT

Reviews:

Related manuals for PCISA-BT

Brands by name

Popular brands