IEI Technology PAC-400AI-C236 User Manual Download Page 67 | Manualshive

Page: 67 / 110

background image

PAC-400AI-C236 Embedded System

Page 57

5.3.9 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 14

) to read USB configuration

information and configure the USB settings.

Aptio Setup Utility – Copyright (C) 2018 American Megatrends, Inc.

Advanced

USB Configuration

USB Controllers:

1 XHCI

USB Devices:

1 Keyboard

Legacy USB Support

[Enabled]

Enables Legacy USB

support. AUTO option

disables legacy support

if no USB devices are

connected. DISABLE

option will keep USB

devices available only

for EFI applications.

---------------------



: Select Screen

↑

↓

: Select Item

Enter: Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

Version 2.18.1263. Copyright (C) 2018 American Megatrends, Inc.

BIOS Menu 14: USB Configuration



Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard
does not become available until a USB compatible operating system is fully booted with all
USB drivers loaded. When this option is enabled, any attached USB mouse or USB
keyboard can control the system even when there is no USB driver loaded onto the system.



Enabled

D

EFAULT

Legacy USB support enabled



Disabled

Legacy USB support disabled



Auto

Legacy USB support disabled if no USB devices are
connected

«
...
65
66
67
68
69
...
»

Summary of Contents for PAC-400AI-C236















































































































Reviews:

No comments

Related manuals for PAC-400AI-C236

Brand: Vahle Pages: 36

Brand: Vahle Pages: 20

Brand: Vacon Pages: 102

RZN 43-E Series

Brand: D+H Pages: 2

Brand: ebm-papst Pages: 10

Brand: BOCK Pages: 38

Brand: ICP DAS USA Pages: 8

Brand: A.B.S. Pages: 30

GUF-Yocto-34.0-r5756-0-VINCELL

Brand: GARZ&FRICKE Pages: 58

ION Performax IQ Easy Ex

Brand: Simco Pages: 33

ZeroVise M Series

Brand: ZeroClamp Pages: 44

Brand: Eaton Pages: 2

BTL5-A/C/E1-MSF-F Series

Brand: Balluff Pages: 16

AutoJet AccuCoat HD15

Brand: Spraying Systems Co Pages: 18

Brand: Baileigh Industrial Pages: 40

KlauKe mini+ EBS6LGKS

Brand: Emerson Pages: 9

Brand: Emerson Pages: 16

Penberthy N2 Series

Brand: Emerson Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands