IEI Technology NANO-ULT5 User Manual Download Page 84 | Manualshive

Page: 84 / 147

background image

NANO-ULT5 SBC

Page 70

Step 3:

Connect power cable to power supply

. Connect one of the 4-pin (1x4) Molex

type power cable connectors to an AT power supply. See Figure 4-19.

Figure 4-19: Connect Power Cable to Power Supply

4.9.2 Audio Kit Installation

The Audio Kit that came with the NANO-ULT5 connects to the audio connector on the
NANO-ULT5. The audio kit consists of three audio jacks. Mic-in connects to a
microphone. Line-in provides a stereo line-level input to connect to the output of an audio
device. Line-out, a stereo line-level output, connects to two amplified speakers. To install
the audio kit, please refer to the steps below:

Step 1:

Locate the audio connector

. The location of the 10-pin audio connector is

shown in

Chapter 3

.

Step 2:

Align pin 1

. Align pin 1 on the on-board connector with pin 1 on the audio kit

connector. Pin 1 on the audio kit connector is indicated with a white dot. See

Figure 4-20

«
...
82
83
84
85
86
...
»

Summary of Contents for NANO-ULT5




















































































































































Reviews:

No comments

Related manuals for NANO-ULT5

Brand: MaxLinear Pages: 25

Brand: EPOX Pages: 83

Brand: Gigabyte Pages: 40

Brand: Texas Instruments Pages: 47

Brand: Biostar Pages: 54

Brand: ECS Pages: 60

FEBFL7701_L31H008A

Brand: Fairchild Pages: 24

Brand: Texas Instruments Pages: 14

Brand: Microchip Technology Pages: 89

Brand: Microsemi Pages: 22

Brand: Texas Instruments Pages: 24

Brand: TYAN Pages: 118

Brand: BCM Pages: 59

Brand: Apex Digital Pages: 7

Brand: DFI Pages: 118

Brand: Asus Pages: 56

Brand: Asus Pages: 46

AT3IONT-I Series

Brand: Asus Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands