IEI Technology NANO-QM871-i1 User Manual Download

Page: 73 / 156

NANO-QM871-i1 EPIC SBC

Page 60

4.9 Internal Peripheral Device Connections

This section outlines the installation of peripheral devices to the onboard connectors.

4.9.1 AT/ATX Power Connection

Follow the instructions below to connect the NANO-QM871-i1 to an AT or ATX power

supply.

WARNING:

Disconnect the power supply power cord from its AC power source to

prevent a sudden power surge to the NANO-QM871-i1.

Step 1:

Locate the power cable

. The power cable is shown in the packing list in

Chapter 2

Step 2:

Connect the Power Cable to the Motherboard

. Connect the 4-pin (2x2) Molex

type power cable connector to the power connector on the motherboard. See

Figure 4-15

Figure 4-15: Power Cable to Motherboard Connection

Summary of Contents for NANO-QM871-i1





























































































































































Search results

Summary of Contents for NANO-QM871-i1

Reviews:

Related manuals for NANO-QM871-i1

Brands by name

Popular brands

IEI Technology NANO-QM871-i1, User Manual

Search results

Summary of Contents for NANO-QM871-i1

Reviews:

Related manuals for NANO-QM871-i1

Brands by name

Popular brands