manualshive.com logo in svg

IEI Technology NANO-6613, User Manual, Page: 83 / 174

Share
Download
IEI Technology NANO-6613 User Manual Download Page 83

 

 

1

-83

NANO-6613 Motherboard 

83

 

F2 /F3 key 

Change color from total 16 colors.    F2 to select color 

forward. 

F10 key 

Save all the CMOS changes, only for Main Menu   

Table 5-1: BIOS Navigation Keys 

5.1.3 Getting Help 

When 

F1

 is pressed a small help window describing the appropriate keys to use and the 

possible selections for the highlighted item appears. To exit the Help Window press 

E

SC

 or 

the 

F1

 key again. 

5.1.4 Unable to Reboot after Configuration Changes 

If the computer cannot boot after changes to the system configuration is made, CMOS 

defaults. Use the jumper described in Chapter 

Chapter 3

, 

Section 3.4.1

. 

5.1.5 BIOS Menu Bar 

The 

menu bar

 on top of the BIOS screen has the following main items: 

 

Main 

Changes the basic system configuration. 

 

Advanced

 

Changes the advanced system settings.

 

 

PCIPnP 

Changes the advanced PCI/PnP Settings

 

 

Chipset 

Changes the chipset settings.

 

 

Boot 

Changes the system boot configuration.

 

 

Security 

Sets User and Supervisor Passwords.

 

 

Exit 

Selects exit options and loads default settings

 

The following sections completely describe the configuration options found in the menu 

items at the top of the BIOS screen and listed above. 

5.2 Main 

When the 

BIOS Setup

 program is entered, the 

Main

 menu (

BIOS Menu 1

) appears. The 

Main

 menu gives an overview of the basic system information.

 

Summary of Contents for NANO-6613















































































































































































Reviews:

No comments