IEI Technology IMB-9452 User Manual Download Page 136

Page: 136 / 188

IMB-9452 Motherboard

AddOn ROM Display Mode [Force BIOS]

Use the

AddOn ROM Display Mode

option to allow add-on ROM (read-only memory)

messages to be displayed.

Force BIOS

EFAULT

The system forces third party BIOS to display

during system boot.

Keep Current

The system displays normal information during

system boot.

Bootup Num-Lock [On]

Use the

Bootup Num-Lock

BIOS option to specify if the number lock setting must be

modified during boot up.

Off

Does not enable the keyboard Number Lock automatically. To

use the 10-keys on the keyboard, press the Number Lock key

located on the upper left-hand corner of the 10-key pad. The

Number Lock LED on the keyboard lights up when the Number

Lock is engaged.

On D

EFAULT

Allows the Number Lock on the keyboard to be enabled

automatically when the computer system boots up. This allows

the immediate use of the 10-key numeric keypad located on

the right side of the keyboard. To confirm this, the Number

Lock LED light on the keyboard is lit.

PS/2 Mouse Support [Auto]

Use the

PS/2 Mouse Support

option adjusts PS/2 mouse support capabilities.

Disabled

PS/2 mouse support is disabled and prevented from

using system resources.

Enabled

Allows the system to use a PS/2 mouse.

Page 136

IEI® Technology, Corp

Summary of Contents for IMB-9452





























































































































































































Search results

Summary of Contents for IMB-9452

Reviews:

Brands by name

Popular brands

IEI Technology IMB-9452, User Manual

Search results

Summary of Contents for IMB-9452

Reviews:

Brands by name

Popular brands