IEI Technology HYPER-BW User Manual Download Page 66

Page: 66 / 102

HYPER-BW

Page 55

5.3.4

RTC Wake Settings

The

RTC Wake Settings

menu (

BIOS Menu 8

) configures RTC wake event.

Advanced

Wake system with Fixed Time

[Disabled]

Enable or disable System

wake on alarm event. When

enabled, System will

wake on the

date::hr::min::sec

specified

----------------------



: Select Screen

↑

↓

: Select Item

Enter Select

F1 General Help

F2 Previous Values

F3 Optimized Defaults

F4 Save

ESC Exit

BIOS Menu 8: RTC Wake Settings



Wake s ys tem with Fixed Time [Dis abled]

Use the

Wake system with Fixed Time

option to enable or disable the system wake on

alarm event.



Disabled

EFAULT

The real time clock (RTC) cannot generate a wake
event



Enabled

If selected, the

Wake up every day

option appears

allowing you to enable to disable the system to wake
every day at the specified time. Besides, the
following options appear with values that can be
selected:

Wake up date

Wake up hour

Wake up minute

Summary of Contents for HYPER-BW







































































































Search results

Summary of Contents for HYPER-BW

Reviews:

Related manuals for HYPER-BW

Brands by name

Popular brands

IEI Technology HYPER-BW, User Manual

Search results

Summary of Contents for HYPER-BW

Reviews:

Related manuals for HYPER-BW

Brands by name

Popular brands