IEI Technology eKINO-BT User Manual Download

Page: 22 / 157

eKINO-BT Mini-ITX SBC

Page 8

1.7 Technical Specifications

The eKINO-BT technical specifications are listed in

Table 1-2

Specification/Model

eKINO-BT

Form Factor

Mini-ITX

Onboard SoC

Intel® Atom™ E3845 (1.91GHz, quad-core, 2MB cache, TDP=10W)

Intel® Atom™ E3827 (1.75GHz, dual-core, 1MB cache, TDP=8W)

Intel® Atom™ E3826 (1.46GHz, dual-core, 1MB cache, TDP=7W)

Intel® Atom™ E3825 (1.33GHz, dual-core, 1MB cache, TDP=6W)

Intel® Atom™ E3815 (1.46GHz, single-core, 512KB cache, TDP=5W)

Intel® Celeron® J1900 (2GHz, quad-core, 2MB cache, TDP=10W)

Intel® Celeron® N2930 (1.83GHz, quad-core, 2MB cache, TDP=7.5W)

Intel® Celeron® N2807 (1.58GHz, dual-core, 2MB cache, TDP=4.5W)

Memory

For J1900, N2930, E3845, E3827and E2826 SKUs:

Two 204-pin 1333/1066 MHz dual-channel unbuffered DDR3L SDRAM

SO-DIMM slots support up to 8 GB

For N2807, E3825 and E3815 SKUs:

One 204-pin 1333/1066 MHz unbuffered DDR3L SDRAM SO-DIMM

slot supports up to 4 GB

* Use DIMM1 slot when installing one SO-DIMM. For the SO-DIMM

slot location, refer to Figure 3-28.

Graphics Engine

Intel® HD Graphics Gen 7 with 4 execution units, supporting

DirectX 11.1, OpenCL 1.2 and OpenGL 4.2

Display Output

One VGA (up to 2560x1600@60 Hz)

Two 18/24-bit dual-channel LVDS* by CH7511B DP to LVDS converters

(up to 1920x1200@60 Hz)

* The eKINO-BT supports only one LCD when using the optional

7.4 V battery (BATKIT-2S2P3800-R10/BAT-LI-2S2P3800).

BIOS

AMI UEFI BIOS

Ethernet

Two Realtek RTL8111E PCIe GbE controllers

Audio

Realtek ALC662 HD Audio codec

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands