IEI Technology eKINO-BT User Manual Download

Page: 24 / 157

eKINO-BT Mini-ITX SBC

Page 10

Environmental and Power Specifications

Power Supply

Input voltage range: 9 V ~ 26 V

Recommended operating input voltage range: 12 V ~ 24 V

One external 4-pin DIN DC jack

One internal 4-pin (2x2) power connector

Power Consumption

[email protected] (Intel® Celeron® J1900 CPU with two 4 GB 1333 MHz

DDR3L memory)

Operating

Temperature

0ºC ~ 40ºC (with AUPS sub-system)

-20ºC ~ 60ºC (without AUPS sub-system)

Storage Temperature

-10ºC ~ 50ºC (with AUPS sub-system)

-30ºC ~ 70ºC (without AUPS sub-system)

Operating Humidity

5% ~ 95% (non-condensing)

Physical Specifications

Dimensions

170 mm x 170 mm

Weight (GW/NW)

1100 g/400 g

Table 1-2: Technical Specifications

Summary of Contents for eKINO-BT






























































































































































Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands

IEI Technology eKINO-BT, User Manual

Search results

Summary of Contents for eKINO-BT

Reviews:

Related manuals for eKINO-BT

Brands by name

Popular brands