IEI Technology AFL-15A-N270 User Manual Download Page 140

Page: 140 / 158

AFOLUX AFL-15A-N270 Panel PC

Page 140

A.1 Motherboard Specifications

The system comes with an IEI AFLMB2-945GSE motherboard. The detailed specifications

for the motherboard are listed below.

Specification

AFLMB2-945GSE

Northbridge

Intel® 945GSE

Southbridge

Intel® ICH7

Processor

1.6 GHz Intel® Atom™ N270 processor

FSB Speed

533 MHz

Supported Memory

One 200-pin 2.0 GB (max.) 400 MHz or 533 MHz DDR2 SDRAM SO-DIMM

(system max. 2.0 GB)

System BIOS

AMI BIOS

Hard disk drives

One SATA drive

VGA

Integrated in the Intel® 945GSE

LAN

Realtek RTL8111CP PCIe GbE Controllers

Expansion Options

One PCIe Mini

Super I/O

ITE IT8718F

Audio Codec

RealTek ALC888

Audio Amplifier

NXP TDA1517P

USB

Four external USB 2.0 ports

RS-232

Fintek

Extra-Module

Optional Bluetooth Module (USB protocol BT-330C-V2)

A.2 Processor Specifications

The N270 Intel® Atom™ processor specifications are given below.

Parameter

Specifications

CPU Speed

1.6 GHz

Bus Speed

533 MHz

L2 Cache Size

512 KB

L2 Cache Speed

1.6 GHz

Manufacturing Technology

45 nm

Summary of Contents for AFL-15A-N270































































































































































Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands

IEI Technology AFL-15A-N270, User Manual

Search results

Summary of Contents for AFL-15A-N270

Reviews:

Related manuals for AFL-15A-N270

Brands by name

Popular brands