background image

 

                                                           

www.hhi-green.com/solar

 
 
 

 

Page 1 of 16 

 

 

Sales Office 

2nd Fl., Hyundai Bldg., 
75, Yulgok-ro, Jongno-gu, 
Seoul 110-793, Korea 

Factory 

 

313, Soi-ro, Soi-myeon, Eumseong-gun, 
Chungcheongbuk-do 369-872, Korea 

INSTALLATION MANUAL 

Effective September 1, 2013

 

1. Introduction

 

·

 

This Installation manual contains information regarding the installation and the safe handling method 
of the photovoltaic module (hereafter referred to as “module”) supplied by Hyundai Heavy Industries 
Co., Ltd. (hereafter referred to as “HHI”). 

·

 

System Users and Installers should read and understand this guide before handling, installing the 
module. For any questions, please contact Customer Support department or our local representatives 
for more detailed information. 

·

 

Before installing a solar photovoltaic system, mechanical and electrical requirements for the total 
system should be checked as well. Keep this guide in a safe place for future reference. 

·

 

The installer should conform to every safety precautions specified in this guide and local codes when 
installing a module.   

·

 

HHI modules are tested and certified for installation worldwide. Different regions may have different 
regulations for solar PV installations. In this manual, hereafter “IEC only” is used to refer to regions 
where IEC standard applies, e.g. Europe, Middle East, most of Asia Pacific countries; “UL only” is 
used to refer to regions where UL standard applies, e.g. United States, Canada; all other references 
are global. 

 

2. General Information 

This manual provides the installation information for HHI modules. Each individual module has a 

unique serial number. 

 

Serial number : YYMMDD-XX-MxxxMG-0001(~9999) (Ex. 110317-21-M235MG-0001) 

 

·

 

YYMMDD : Production date 

·

 

XX : Production line 

·

 

MxxxMG : Model (xxx : module power range) 

·

 

0001(~9999) : Production number 

 

2.1   Disclaimer of Liability 

·

 

The information in this manual is based on HHI’s knowledge and experience and is believed to be 
reliable; but any information including product specification (without limitations) and descriptions do 
not constitute over a warranty. 

·

 

HHI reserves the rights for any change the technical specification including the PV production, the 
specifications, or the product information sheets without prior notice. 

·

 

The installation techniques, handling and use of this product are beyond company control. 

·

 

HHI does not have any responsibility and the liability for loss, damage, injury or expense resulting 
from improper installation, handling or use. 

 

Summary of Contents for HiS-MxxxMF

















Reviews: