iDule ID2MB-CLIR Technical Manual Download Page 29

Page: 29 / 35

Function Setting

Function

Address(Hex)

Data(Hex)

Shutter

2Tap
Base Configuration

4Tap
Medium Configuration

8Tap
Full Configuration

00:

1/70s(OFF)

1/140s(OFF)

1/280s(OFF)

01:

1/140s

1/140s(OFF)

1/280s(OFF)

02:

1/280s

1/280s(OFF)

03:

1/350s

04:

1/500s

05:

1/1000s

06:

1/2500s

07:

1/5000s

08:

1/7500s

09:

1/10000s

0A:

1/15000s

0B:

1/20000s

0C:

1/30000s

0D:

1/30000s

1/40000s

0E:

1/30000s

1/40000s

1/50000s

0F:

Manual (Refer to Address 24-25)

Trigger Mode

00:

Normal (Trigger OFF)

01:

Fixed Trigger Shutter Mode

02:

Pulse Width Trigger Shutter Mode

Trigger Polarity

00:

Positive

01:

Negative

Partial Scan Mode

00:

Full Frame

01:

Partial Scan

Output Mode

00:

8Tap Full Configuration (280fps)

01:

4Tap Medium Configuration (140fps)

02:

2Tap Base Configuration (70fps)

03:

04:

2Tap Base Configuration Center Trimming 512(H)

05:

2Tap Base Configuration Center Trimming 1024(H)

06:

07:

Output Data Selection

00:

8bit

01:

10bit (8Tap Full Configuration : 8bit only)

Summary of Contents for ID2MB-CLIR




































Search results

Summary of Contents for ID2MB-CLIR

Reviews:

Related manuals for ID2MB-CLIR

Brands by name

Popular brands

iDule ID2MB-CLIR, Technical Manual

Search results

Summary of Contents for ID2MB-CLIR

Reviews:

Related manuals for ID2MB-CLIR

Brands by name

Popular brands