IDTECK Star iCON100 Quick Installation Manual Download Page 15 | Manualshive

Page: 15 / 24

background image

※

iCON100/iCON100-SR QUICK INSTALLATION GUIDE

15



Alarm Device Connection (Relay #2)

- Connect COM port of Relay #2 to DC+12V

- Connect NO port of Relay #2 to (+) wire of Alarm devices
- Connect GND port to (-) wire of Alarm devices

Figure: Door Lock, Al

arm Device Connection

Caution: You need to connect the diode ( 1N4001 ~ 1N4007 or Similar) when connecting external devices to

relay.

5.4.4 Reader Connections



Proximity Reader Connection

- Connect (+) wire of the Proximity Reader to DC+12V of Reader port
- Connect (-) wire of the Proximity Reader to GND of Reader port

- Connect Data-0 wire of the Proximity Reader to D0 of Reader Port
- Connect Data-1 wire of the Proximity Reader to D1 of Reader Port



Compatible Readers

:

- iCON100:

Standard 26bit Wiegand Format Proximity Readers, Standard 26bit W 8bit Burst

Format Proximity and Keypad Readers.

- iCON100SR:

Standard 34bit Wiegand Format Proximity Readers, Standard 34bit Wiegand + 8bit

Burst Format Proximity and Keypad Readers.

Figure: Reader Connection

«
...
13
14
15
16
17
...
»

Summary of Contents for Star iCON100

























Reviews:

No comments

Related manuals for Star iCON100

Brand: Samson Pages: 48

Brand: Mako Networks Pages: 15

Brand: UNITED Pages: 8

Brand: Febco Pages: 12

Brand: Game ready Pages: 21

Brand: VAMP Pages: 304

Brand: K'Nex Education Pages: 56

Tissue-Tek TEC 6

Brand: Sakura Seiki Pages: 6

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Watlow Pages: 59

Tekmar WiFi Snow Melting Control 670

Brand: Watts Pages: 48

Brand: National Instruments Pages: 78

PowerFlex 755 IP00

Brand: Allen-Bradley Pages: 78

Brand: ISVT Pages: 78

Brand: Linear Technology Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands