background image

   
   
   
 

 

                 

12 

 

 

                                       

 

12. FCC Registration Information 

 

FCC REQUIREMENTS PART 15 

 
Caution: Any changes or modifications in construction of this device which are not expressly   

approved by the manufacturer for compliance could void the user's authority to operate the 
equipment. 

 
NOTE: This device complies with Part 15 of the FCC Rules
 
Operation is subject to the following two conditions; 
1. This device may not cause harmful interference, and 
2. This device must accept any interference received, including interference that may cause undesired   

operation. 

 
This equipment has been tested and found to comply with the limits for a Class B Digital Device
pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates, uses, and 
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment 
does cause harmful interference to radio or television reception, which can be determined by turning the 
radio or television off and on, the user is encouraged to try to correct interference by one or more of the 
following measures. 
 
1. Reorient or relocate the receiving antenna. 
2. Increase the separation between the equipment and receiver. 
3. Connect the equipment into an outlet on another circuit. 
4. Consult the dealer or an experienced radio/TV technician for help. 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for SR10S

















Reviews: