IDTECK iMDC-MAIN User Manual Download Page 26

Page: 26 / 79

INSTALLATION TIPS & CHECK POINTS

p.20

RECOMMENDED CABLE TYPE AND PERMISSIBLE LEN

GTH OF CABLE

Reference

Description

Cable specification

Maximum distance

DC +12V → Power iMDC-MAIN

DC +12V → Power iMDC-RIM

Belden #9409, 18 AWG

2 conductor, unshielded

Reader (Power and Data)

Reader → iMDC-RIM

Belden #9512, 22 AWG

4 conductor, shielded

150m

Belden #9514, 22 AWG

8 conductor, shielded

Door Contact

Exit Button

Sensor Input

Input → iMDC-RIM

Belden #9512, 22 AWG

4 conductor, shielded

300m

Belden #9514, 22 AWG

8 conductor, shielded

Door Lock, Alarm Device

Lock (Alarm) → iMDC-RIM

Belden #9409, 18AWG

2 conductor, unshielded

300m

iMDC Cable

iMDC-RIM Cable

iMDC-MAIN ↔ iMDC-MAIN

iMDC-MAIN ↔ iMDC-RIM

iMDC-MAIN ↔ Host P.C

UTP Cable CAT5(Catagory5)

100m

150m

CHECK POINT DURING INSTALLATION

3.1

REVERSE DIODE CONNECTION

If you connect an inductor (Door Locks or Alarm device) to the output relays, there will be a

high surge voltage created while the inductor is turning on and off. To protect this problem,

connect the reverse diode as the figure below.

1 You need thicker wire if you connect the reader with high current consumption

Summary of Contents for iMDC-MAIN
















































































Search results

Summary of Contents for iMDC-MAIN

Reviews:

Related manuals for iMDC-MAIN

Brands by name

Popular brands

IDTECK iMDC-MAIN, User Manual

Search results

Summary of Contents for iMDC-MAIN

Reviews:

Related manuals for iMDC-MAIN

Brands by name

Popular brands