IDT VersaClock 6 5P49V69 Series User Manual Download Page 10

DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document,
including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not
guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the
suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any
license under intellectual property rights of IDT or any third parties. 

IDT’s products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to signifi-
cantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.

Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Product specification subject to change without notice. Other trademarks and service marks used herein, including protected names, logos and
designs, are the property of IDT or their respective third party owners.

Copyright 2015. All rights reserved. 

Corporate Headquarters

6024 Silver Creek Valley Road 
San Jose, CA 95138 USA

Sales

1-800-345-7015 or
408-284-8200 
Fax: 408-284-2775
www.IDT.com

Support

www.idt.com/go/support

VERSACLOCK

®

 6 - 5P49V69xx Family Programmer Board

Summary of Contents for VersaClock 6 5P49V69 Series











Reviews: