manualshive.com logo in svg

IDT Tsi578, User Manual

The IDT Tsi578 is a high-performance networking switch, and to help you make the most out of its features, we provide a comprehensive User Manual. This manual is available for free download from our website, ensuring effortless access to valuable product information and instructions for optimal usage.

Share
Download
background image

65

Tsi578 User Manual

June 6, 2016

Integrated Device Technology

www.idt.com

3. 

Serial RapidIO Electrical Interface

This chapter describes the IDT-specific electrical layer features of the Tsi578 Serial RapidIO Electrical 
Interface. See the 

“Serial RapidIO Interface”

 for a description of the standards-defined RapidIO 

features common to all RapidIO ports. 

This chapter includes the following information:

•

“Overview” on page 65

•

“Port Numbering” on page 67

•

“Port Aggregation: 1x and 4x Modes” on page 68

•

“Clocking” on page 70

•

“Port Power Down” on page 72

•

“Port Lanes” on page 74

•

“Programmable Transmit and Receive Equalization” on page 77

•

“Port Loopback Testing” on page 79

•

“Bit Error Rate Testing (BERT)” on page 80

3.1

Overview

The Tsi578 has eight Media Access Controllers (MAC) comprising the 16 Serial RapidIO ports. The 16 
ports are grouped into pairs consisting of one even numbered port and one odd numbered port. Each 
port has flexible testing features including multiple loopback modes and bit error rate testing. Each pair 
of ports share four differential transmit lanes and four differential receive lanes. 

Even and odd number ports have different capabilities. Even numbered ports can operate in either 4x or 
1x mode, while odd numbered ports can only operate in 1x mode. When the even numbered port is 
operating in 4x mode, it has control over all four differential pairs (designated Lanes A, B, C and D). In 
4x mode, the default state of the odd numbered port is powered on. All registers in the even and odd 
numbered port are accessible but the odd numbered port does not have access to the PHY. In order to 
decrease the power dissipation of the port, the odd numbered port can be powered down in this 
configuration. When the even numbered port is operating in 1x mode it uses only Lane A and the odd 
numbered port is permitted to operate in 1x mode using Lane B.

The Tsi578 MAC and SerDes interconnect block diagram is shown in the following figure.

Summary of Contents for Tsi578
















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Tsi578

Cabletron Systems SmartSwitch 9A100 Installation And Setup Manual preview
SmartSwitch 9A100
Brand: Cabletron Systems Pages: 52
Cabletron Systems SmartSwitch 9W006 Quick Start Manual preview
SmartSwitch 9W006
Brand: Cabletron Systems Pages: 34
Cabletron Systems SmartSTACK ELS100-S24TX2M Management Manual preview
SmartSTACK ELS100-S24TX2M
Brand: Cabletron Systems Pages: 102
Cabletron Systems 9A426-01 Appendix preview
9A426-01
Brand: Cabletron Systems Pages: 24
Cabletron Systems SmartSwitch 9000 Appendix preview
SmartSwitch 9000
Brand: Cabletron Systems Pages: 14
Cabletron Systems MicroMMAC 22ES Reference Manual preview
MicroMMAC 22ES
Brand: Cabletron Systems Pages: 38
Fema DCM Series Assembly And Operating Instructions Manual preview
DCM Series
Brand: Fema Pages: 96
LaCie 1big Dock SSD Pro Quick Install Manual preview
1big Dock SSD Pro
Brand: LaCie Pages: 28
D-Link DMS-1250 Series Hardware Installation Manual preview
DMS-1250 Series
Brand: D-Link Pages: 38
Ihse Draco major K474-U8/C8 User Manual preview
Draco major K474-U8/C8
Brand: Ihse Pages: 167
steute Ex 95 SB Mounting And Wiring Instructions preview
Ex 95 SB
Brand: steute Pages: 10
Xantech 680-10 Installation Instructions preview
680-10
Brand: Xantech Pages: 4
Synology NEXT-POE4210L2S-TP Quick Installation And Initial Configuration preview
NEXT-POE4210L2S-TP
Brand: Synology Pages: 15
N-Tron 716M12 User Manual & Installation Manual preview
716M12
Brand: N-Tron Pages: 169
Leonton EG2-1600 Series User Manual preview
EG2-1600 Series
Brand: Leonton Pages: 19
WAGO 852-1111 Mounting, Installation And Handling preview
852-1111
Brand: WAGO Pages: 36
Contemporary Controls CTRLink EISK8P-GT Installation Manual preview
CTRLink EISK8P-GT
Brand: Contemporary Controls Pages: 4
InvoTek BlueHub User Manual preview
BlueHub
Brand: InvoTek Pages: 4

Brands by name

Popular brands

Load more brands