IDT CPS-1848 User Manual Download Page 64 | Manualshive

Page: 64 / 450

background image

2. RapidIO Ports > Packet Transfer Validation and Debug

CPS-1848 User Manual

64

June 2, 2014

Formal Status

This document is confidential and is subject to an NDA.

Integrated Device Technology

The configuration and status values for the port that are relevant to packet reception are listed in

Port {0..17} Filter Match Counter Value
0 Register

through

Port {0..17} Filter

Match Counter Value 3 Register

This counter indicates the number of received
packets that the switch filtering mechanism
has dropped.

Packets are being dropped because they are
filtered. Check that the correct packets are
being filtered.

Port {0..17} VC0 Received Packets
Dropped Counter Register

This counter indicates the number of packets
dropped by the receive port.

Packets are being dropped due to error status,
routing configuration, or other configuration
issues.

Table 16: Configuration and Status Values to Check – Switch Cannot Accept Packets

Packet Counter Register

Bit Field

Debug Notes

Port {0..17} Error and Status CSR

PORT_OK

If this bit is set to 0, the link is not connected to
the link partner. For more information, see the
Debugging IDT S-RIO Gen2 Switches Using
RapidFET JTAG.

PORT_ERR

If this bit is set to 1, the standard hardware
error recovery has failed. For more
information, see

HS-LP Controlled Recovery

.

INPUT_ERR_STOP

If this bit is set to 1, the switch input port has
detected an error and error recovery is not
complete. Check that the

Port Link Timeout

has been initialized according to

the guidelines in

Port {0..17} Control 1 CSR

PORT_DIS

This bit must be cleared to allow the port to
train.

INPUT_PORT_EN

This bit must be set to allow the port to accept
non-maintenance packets.

PORT_LOCKOUT

This bit must be cleared to allow the port to
accept packets.

Port {0..17} Implementation Specific
Error Detect Register

RTE_ISSUE

Packet received that is dropped according to
the conditions for this event. For more
information, see the description of this bit field.

RX_DROP

Reception of non-maintenance packets has
been disabled (see INPUT_PORT_EN).

Table 15: Packet Counters and Configuration Issues – Switch Cannot Accept Packets

Packet Counter Register

Description

Implication

«
...
62
63
64
65
66
...
»

Summary of Contents for CPS-1848



































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CPS-1848

Brand: GE Pages: 36

Brand: GE Pages: 8

Brand: Eaton Pages: 40

Brand: 3Com Pages: 1133

Brand: SMC Networks Pages: 102

Brand: IOGear Pages: 1

Brand: SIIG Pages: 17

Brand: Woxcon Pages: 42

MMAC-Plus 9T125-24

Brand: Cabletron Systems Pages: 36

Brand: Raritan Pages: 4

Brand: Videplus Pages: 13

Brand: cable matters Pages: 8

SICOM3028GP Series

Brand: KYLAND Technology Pages: 40

Brand: Edimax Pages: 2

IPES/IES-5416T Series

Brand: Lantech Pages: 27

Brand: Justin Pages: 8

Sure-Wave CM-330/N

Brand: CAMDEN Pages: 4

CyberSWITCH CSX150

Brand: Cabletron Systems Pages: 620

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands