manualshive.com logo in svg

IDK MSD-702UHD, User Manual

Share
Download
IDK MSD-702UHD User Manual Download Page 91

MSD-701UHD / 702UHD / 801UHD/ 802UHD  User’s Guide 

91 

9.11.2  RS-232C operation mode 

Menu        Top

→

COM PORT

→

FUNCTION 

Setting for        RS-232C connector, OUT1B connector, OUT2B connector, IN8 connector 

Setting value  RECEIVER,TRANSMITTER 

 

[Default] 

 

RS-232C connector, IN8 connector: RECEIVER 

 

OUT1B connector, OUT2B connector: TRAMSMITTER 

 

You can set the operation mode to “RECEIVER” mode in which the MSD is controlled externally or 

“TRANSMITTER” mode in which the MSD controls peripheral devices. 

The setting of this menu is not updated until the MENU/SET key is pressed. Make sure to press the 

MENU/SET key to update the setting. 

 

9.11.3  RS-232C HDBaseT connection 

Menu        Top

→

COM PORT

→

OUT B SCI CONNECT 

Setting value  

[Table 9.18] RS-232C operation

 

 

You can set the communication between MSD’s RS-232C connector and an RS-232C connector of twisted 

pair cable transmitter or receiver that is connected to HDBaseT I/O connector. 

 

[Table 9.18] RS-232C operation 

Setting value 

Operation 

OFF  [Default] 

MSD’s RS-232C connector operates in the mode that is set in “

9.11.2 RS-232C operation 

mode

”. 

OUT1B 

Communication between MSD’s RS-232C connector and an RS-232C connector of 

twisted pair cable transmitter or receiver that is connected to HDBaseT I/O connector. 

The MSD’s RS-232C connector cannot be used for communication command control from 

PC to MSD or control command output from MSD to external devices.   

OUT2B 

IN8 

 

【

See: 9.11 RS-232C

】

 

 

 

Summary of Contents for MSD-702UHD























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands