IDK MSD-702UHD User Manual Download Page 90

Page: 90 / 150

MSD-701UHD / 702UHD / 801UHD/ 802UHD User’s Guide

9.11 RS-232C

The RS-232C connector of the MSD can output communication command control from PCs and can output

control command to external devices from the MSD. The operation mode will be switched according to “

9.11.2

RS-232C operation mode

”.

【

See: 9.13 Setting control command

】

Laptop

Projector

RS-232C cable

Twisted pair cable

RS-232C cable

Communication command control to MSD

Outputting control commands to

external devices

Outputting control commands to external devices

Power amp.

IN8

RS-232C transmission setting between control
devices (OUT B SCI CONNECT)

Not connected (RS-232C connector operates normally)

Twisted pair cable

receiver

[Fig. 9.21] RS-232C communication

9.11.1 RS-232C communication setting

Menu Top

→

COM PORT

→

PARAMETERS

Setting for RS-232C connector, OUT1B connector, OUT2B connector, IN8 connector

Setting value

[Table 9.17] RS-232C setting items

Setting item

Setting value

Default

Baud rate [bps]

4800, 9600, 19200, 38400

9600

Data bit length [bit]

8, 7

Parity check

NONE, EVEN, ODD

NONE

Stop bit [bit]

1, 2

You can set RS-232C communication.

The setting of this menu is not updated until the MENU/SET key is pressed. Make sure to press the

MENU/SET key to update the setting.

Summary of Contents for MSD-702UHD























































































































































Search results

Summary of Contents for MSD-702UHD

Reviews:

Brands by name

Popular brands

IDK MSD-702UHD, User Manual

Search results

Summary of Contents for MSD-702UHD

Reviews:

Brands by name

Popular brands