197
6.17.4
Configuring A Foam Quickset
If a foam discharge is used often and is typically initialized by SAM create a foam Quickset for the
discharge as follows.
A.
Enter system options.
Touch (and hold if required) until loading icon completes a circle.
Enter appropriate password to access Display Menu (see Table 6).
Display tab is displayed by default.
B.
If required, touch Display tab. When displayed, touch DISCHARGE QUICKSETS
button.
C.
If Quickset(s) already exist, perform How To Change The Order Of (Or Delete)
Quicksets On The Home Screen (paragraph 6.2.2.2, page 189).
D.
Perform Assigning Quicksets To The Home Screen (paragraph 6.2.2.1, page 189).
6.18.
Connecting Captium To SAM
To connect SAM to Captium, connect the following SAM CAN buses to the associated Captium
CAN bus. See Table 77 for details.
•
SAM Blue CAN bus to Captium CAN bus 1.
•
SAM Green CAN bus to Captium CAN bus 2.
•
SAM Red CAN bus to Captium CAN bus 3.
Use a CAN extension cable [M – M] (P/N 116971) to interconnect each bus.
(Relocate the termination resistor(s) if required.)
Table 84. Captium To SAM Wiring (From/To Listing)
Captium Display
(Green) Connector 1 (Pin)
To SAM Control Center
Black Connector
To Pump Controller
Connector A (Black)
12 (CAN1 Low) [Bus]
N/A
5 (CAN1 Low)
[Bus]
1
(CAN1 High) [Bus]
N/A
6 (CAN1 High)
[Bus]
10 (CAN2 Low) [Bus]
5 (CAN1 Low)
[Bus]
18 (CAN2 Low)
[Bus]
3
(CAN2 High) [Bus]
6 (CAN1 High)
[Bus]
19 (CAN2 High)
[Bus]
9
(CAN3 Low) [Bus]
18 (CAN2 Low)
[Bus]
N/A
4
(CAN3 High) [Bus]
19 (CAN2 High)
[Bus]
N/A
Pins 2, 11, and 8 are shields. CAN shield pins NOT provided. CAN shields NOT provided.
6.18.1
Configuring Captium For SAM
Hale Captium is configured and tested by Hale before it is shipped loose. See the subparagraph
below for details.
6.19.
Saving The Configuration Changes
Perform the following to save the configuration changes including friendly name and/or colors
associated with a discharge valves icon displayed on any of the SAM Control Center screens
(quicksets, discharge settings, or manual valve control screens).
A.
On EDIT VALVE screen, touch HOME icon/button.
(top center of screen, see Figure 159, page 189).
B.
On SELECT DEVICE screen, touch MENU icon/button
(top center of screen, see Figure 158, page 188).
Summary of Contents for Hale Sam
